Launch offer — valid today only

📄 Digital book in PDF · read it on your phone or print it

Water and Wastewater Process Control, in Drawings One Stage on Every Page

Classes I to VI, works maths, coagulation and the jar test, filters and backwashing, the breakpoint curve, activated sludge and sludge age, digesters and chlorine safety. Every topic has its own page: the drawing first, then what you need to remember. 64 illustrated pages.

I WANT THE BOOK AND THE 2 GIFTS

🔒 Secure checkout · PDF by email · 30-day guarantee

Every topic, its own pageEvery stage and every calculation drawn, with the explanation alongside
64 illustrated pages8 parts, from process controller classes to the shift checklist
Up-to-date sourcesRegulation 3630, SANS 241 and the Water Services Act
PDF by emailFormat

Look Inside the Book

Every page has a large drawing and a box with the numbers and steps you need to know:

Class I to VI under Regulation 3630 of 2023: Class V and VI need Pr.PC.Water registration.
Class I to VI under Regulation 3630 of 2023: Class V and VI need Pr.PC.Water registration.
1 ML = 1 000 m³ · 1 m³ = 1 000 L · 1 ML/d ≈ 41.7 m³/h
1 ML = 1 000 m³ · 1 m³ = 1 000 L · 1 ML/d ≈ 41.7 m³/h
Intake to reservoir in eight boxes, with what each stage removes
Intake to reservoir in eight boxes, with what each stage removes
Dose 3.0 mg/L − residual 0.5 mg/L = demand 2.5 mg/L, solved both ways.
Dose 3.0 mg/L − residual 0.5 mg/L = demand 2.5 mg/L, solved both ways.
Screens → grit → primary → biological → secondary → disinfection, with sludge handled on the side
Screens → grit → primary → biological → secondary → disinfection, with sludge handled on the side
Aeration basin, clarifier, RAS and WAS drawn as one loop.
Aeration basin, clarifier, RAS and WAS drawn as one loop.
Digester at around 35 °C: rising volatile acids to alkalinity ratio is the early warning.
Digester at around 35 °C: rising volatile acids to alkalinity ratio is the early warning.
Raw water to tap in six blocks: ≤1 NTU after filters, 0.5 mg/L free chlorine leaving the works.
Raw water to tap in six blocks: ≤1 NTU after filters, 0.5 mg/L free chlorine leaving the works.

Swipe to see more →

These are real pages from the book. The table of contents is the full one: 8 parts and 60 topics.

The Problem Isn't You. It's How It Was Explained to You.

You're on shift and a new operator asks you to walk him through the works, from intake to reservoir. You see it every day, but the order of the stages won't come out in words.

The manual has it all, spread over chapters of paragraphs: coagulation here, filtration somewhere else, nothing joining them. You read it, and the next day it's a blur.

Intake to reservoir in eight boxes, with what each stage removes

In this book the water works is one page: intake to reservoir in eight boxes, each one with what that stage removes. You follow the arrows from left to right.

The rest works the same way: the jar test, the breakpoint curve, sludge age, the 30-minute settling test, the digester. Each one has its own page.

You explain the works in order, you work out the dose and you answer without going back to the manual.

COMPARE FOR YOURSELF

The Same Topic, Two Ways to Study It

THIS
  • The manual: line after line
  • Unit conversions explained in words only
  • You reach the shift or the assessment unsure
Flow rates at water and wastewater treatment works are expressed in a variety of units depending on the context of measurement, and the operator is required to convert between them accurately. One megalitre is equivalent to one thousand cubic metres, while one cubic metre corresponds to one thousand litres. Where plant throughput is stated in megalitres per day, conversion to cubic metres per hour is obtained by multiplying by one thousand and dividing by twenty-four, giving approximately 41.7 m³/h for each ML/d, a value to be applied consistently.
FOR THIS
  • The units of the works in one drawing
  • The conversions in a box
  • You see it and you get it
1 ML = 1 000 m³ · 1 m³ = 1 000 L · 1 ML/d ≈ 41.7 m³/h
CONTENTS

Take a Look at the 8 Parts and 60 Topics

The works and the rules, works maths, drinking water treatment, chlorine and disinfection, wastewater from inlet to primary, activated sludge, sludge, lab and safety, and revision: 64 pages, all illustrated.

IThe Works and the Rules · pp. 5-10
  1. Process controller classes I to VI
  2. How a works is classified: A to E
  3. What a process controller is responsible for
  4. The logbook: what to write and when
  5. SANS 241 at a glance
  6. Wastewater effluent limits: why they exist
IIWorks Maths Without Freezing · pp. 11-18
  1. mg/L, ML/d and m³/h: the units of the works
  2. The kg per day rule
  3. Dosing with a chemical that is not 100%
  4. Retention time
  5. Surface overflow rate
  6. Areas and volumes of works tanks
  7. Dosing pump settings from a dose
  8. Percent removal
IIIDrinking Water Treatment · pp. 19-28
  1. The water works as a block diagram
  2. Raw water: what comes in
  3. Coagulation: neutralising the charge
  4. The jar test step by step
  5. Flocculation: building the floc
  6. pH and alkalinity in coagulation
  7. Sedimentation: the clarifier cross-section
  8. Rapid gravity filters inside
  9. When to backwash
  10. Stabilisation and final pH
IVChlorine and Disinfection · pp. 29-35
  1. Dose = demand + residual
  2. The breakpoint curve
  3. Free and combined chlorine
  4. pH changes how chlorine works
  5. Contact time: the CT idea
  6. Chlorine gas, HTH and sodium hypochlorite
  7. Keeping a residual in the network
VWastewater: Inlet to Primary · pp. 36-41
  1. The wastewater works as a block diagram
  2. What is in raw sewage
  3. Screens and grit channels
  4. Measuring flow: Parshall flume and weirs
  5. Primary settling tanks
  6. Trickling filters (biofilters)
VIActivated Sludge · pp. 42-51
  1. How activated sludge works
  2. MLSS and MLVSS
  3. Sludge age, calculated
  4. F/M ratio
  5. Dissolved oxygen in the aeration basin
  6. The 30-minute settling test and SVI
  7. Bulking, foaming and rising sludge
  8. Nitrification and denitrification
  9. Biological phosphorus removal
  10. Secondary clarifier and RAS rate
VIISludge, Lab and Safety · pp. 52-59
  1. Anaerobic digesters
  2. Sludge drying beds and dewatering
  3. Taking a representative sample
  4. Turbidity, pH and chlorine tests at the works
  5. Chlorine safety
  6. Confined spaces and H₂S
  7. Pumps at the works
  8. Reporting a non-compliance
VIIIRevision and Exam Prep · pp. 60-64
  1. The whole water works on one page
  2. The whole wastewater works on one page
  3. Formula sheet
  4. Frequent calculation mistakes
  5. Shift checklist

One Page, One Topic, All Clear

Think of it this way:

It's the end of the month and the supervisor wants the sludge age for the report. You have the MLSS, the wasting rate and a blank page.

You open the book at sludge age. The aeration basin and the clarifier are drawn, the sludge leaving the system is marked, and the sum is solved step by step, in the same order as every other calculation.

Screens → grit → primary → biological → secondary → disinfection, with sludge handled on the side

The same goes for the breakpoint curve, the jar test, backwashing, the F/M ratio and confined spaces: each one on its own page.

Water Process Controller Illustrated is 8 parts and 60 topics, all drawn, ending with both works on one page each, a formula sheet, the frequent calculation mistakes and a shift checklist.

What you see drawn, you don't have to memorize.

What's Inside Water Process Controller Illustrated:

Ipp. 5-10

The Works and the Rules

Process controller classes I to VI, how a works is classified from A to E, what you are responsible for, the logbook, how to read a result against SANS 241 and why effluent limits exist.

IIpp. 11-18

Works Maths Without Freezing

The units of the works, the kg per day rule, dosing with a chemical that isn't 100%, retention time, surface overflow rate, tank volumes, dosing pump settings and percent removal.

IIIpp. 19-28

Drinking Water Treatment

The water works as a block diagram, raw water, coagulation, the jar test, flocculation, pH and alkalinity, the clarifier, rapid gravity filters, when to backwash and final pH.

IVpp. 29-35

Chlorine and Disinfection

Dose = demand + residual, the breakpoint curve, free and combined chlorine, how pH changes chlorine, contact time, gas, HTH and hypochlorite, and keeping a residual in the network.

Vpp. 36-41

Wastewater: Inlet to Primary

The wastewater works as a block diagram, what's in raw sewage, screens and grit channels, Parshall flumes and weirs, primary settling tanks and trickling filters.

VIpp. 42-51

Activated Sludge

How activated sludge works, MLSS and MLVSS, sludge age, F/M ratio, dissolved oxygen, the 30-minute settling test and SVI, bulking and foaming, nitrogen and phosphorus removal, and the RAS rate.

VIIpp. 52-59

Sludge, Lab and Safety

Anaerobic digesters, drying beds and dewatering, taking a representative sample, turbidity, pH and chlorine tests, chlorine safety, confined spaces and H₂S, pumps and reporting a non-compliance.

VIIIpp. 60-64

Revision and Exam Prep

The whole water works and the whole wastewater works on one page each, the formula sheet, frequent calculation mistakes and a shift checklist.

At the end of the book: Both works on one page each, a formula sheet, the frequent calculation mistakes and a shift checklist.

Plus: 2 Free Books

Process Controller Practice Questions

BONUS 1: «Process Controller Practice Questions»

Value on its own: US$ 17.90

Exam-style questions with worked answers on treatment, calculations and safety, so you can test yourself before registration.

15 Common Works Mistakes: Before and After

BONUS 2: «15 Common Works Mistakes: Before and After»

Value on its own: US$ 14.90

The most frequent mistakes at the works, from wrong chlorine dosing to late backwashing, each drawn next to the right way.

Water Process Controller Illustrated with 2 Free Books

  • Water Process Controller Illustrated: 64 illustrated pagesUS$ 63
  • BONUS 1: Process Controller Practice QuestionsUS$ 17.90
  • BONUS 2: 15 Common Works Mistakes: Before and AfterUS$ 14.90
  • High-resolution PDF to printIncluded
Total value US$ 95.80
YOUR PRICE:
US$ 27
You save US$ 68.80
YES, I WANT WATER PROCESS CONTROLLER ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

Secure purchaseEncrypted payment30-day guarantee

PDF by email: We email you Water Process Controller Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.

Who This Book Is For

You're studying for registration

You're studying for registration

Every stage of the works and every calculation is drawn on its own page, so you study the plant in the order it really runs.

Your registration or class upgrade is close

Your registration or class upgrade is close

The revision part puts both works on one page each, with a formula sheet, so you can go over everything calmly in an evening.

You already run shifts at the works

You already run shifts at the works

Print the pages you use most, like the chlorine dose or the units of the works, and keep them next to the logbook.

Everything You Get Today

US$ 95.80US$ 27
YES, I WANT WATER PROCESS CONTROLLER ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

30DAYS
GUARANTEE

30-Day Guarantee

Try Water Process Controller Illustrated for 30 days, bonus books included.

We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.

You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've worked at the works for years but I'm still registered at a low class?

Yes. It isn't a beginner's book: it shows why the works does what it does and solves every calculation step by step, to help you prepare to register or move up a class.

Where does the content come from?

It's written for South African works: metric units (ML/d, m³/h, mg/L, kg/d), process controller classes I to VI, works classes A to E, and the limits you report against. It isn't an American book adapted. The content is checked against Regulation 3630, the Water Services Act, the National Water Act, SANS 241, the General Authorisation effluent limits and the Occupational Health and Safety Act 85 of 1993, cited for reference.

Is it official material?

No. It's an independent study book. It isn't issued, approved or endorsed by the Department of Water and Sanitation, the SABS or any other body.

Does it replace a course or training?

No. It doesn't replace accredited training, experience on the job or your works' operating procedures, and it doesn't give you a certificate or count as credits towards registration. It's a study book to help you understand and revise before you register or move up a class.

Are the practice questions the ones in the exam?

No. They're written for this book, in exam style, so you can test yourself. They aren't official questions from any exam or assessment.

When and how do I receive it?

The book and the 2 gifts arrive as a PDF by email, at the address you enter when you pay.

Do I have to pay every month?

No. It's a once-off payment.

Can I have it on paper?

Yes. The PDF prints on A4, so you can keep the pages you use most at the works.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

Before You Close This Page

No more rereading without anything sticking.

The water works, stage by stage: you see it drawn and that's it.

You reach the shift or your registration knowing where everything is.

Drawings make studying faster.

The book is right below.

One-time payment: US$ 27 · Guarantee: 30 days · PDF by email

YES, I WANT WATER PROCESS CONTROLLER ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.